Featured Products

Yard Hydrants

Pitless Adapters

Well Caps

Torque Arrestors

Well Diagram

Residential

Filtration Products

Water Well Products

Water Well Accessories

Installation and Electrical Accessories

Sewage Pump Disconnects

Industrial

  • Pitless Units

    Booster Stations

    Protective Wall Enclosure

    • VISIT MONITOR INDUSTRIAL

    • Environmental

    • Video

    • Where to Buy

    Feature Comparison* – Boshart Pitless Adapter "Kit" vs Monitor Pitless Unit

    *Boshart has introduced a Standard Pitless Adapter Complete Unit, but continues to offer a Pitless Adapter "Kit". The following comparison indicates the differences between a Boshart Pitless Adapter "Kit" and a Monitor Pitless Unit. The Monitor Pitless Unit is shipped to your job site fully assembled allowing for a quick installation. The Boshart Pitless Adapter "Kit" requires extensive field welding, additional labor, and cumbersome installation. The Monitor Pitless Unit provides many standard features whereas the Boshart Pitless Adapter "Kit" offers our standard features as accessory or options only. The complete Monitor Pitless Unit is third party certified by NSF to NSF/ANSI 61 & 372 standards. On the Boshart Pitless Adapter "Kit", only the paint is certified to NSF 61 standards. This is NOT an equivalent certification. Please visit NSF's website.

     

    Boshart Pitless Adapter “Kit”
    8" - 12" available well sizes
    1. Optional: Depth Test Kit
      Contractor must drill hole thru the upper casing in the field. Must purchase AC-2 Depth Tester Kit, resulting in additional cost and time. Mandatory in some states.
    2. Optional: Upper Case and Lift-Out Pipe
      Contractor must Engineer and Fabricate Upper Case to appropriate length. Lift-Out pipe requires field threading on both ends for Spool / Torque Arrestor Connections. State codes may require the full assembly to be fabricated at the factory. * NOT PERMITTED IN ALL STATES *
    3. Contractor Required to Field weld Flange to Upper Case
      Contractor must procure flange, gasket and hardware for Upper Case connection, resulting in additional cost and time. * FIELD WELDING REQUIRED *
    4. Contractor Required to Field weld Flange to Well Casing
      Contractor must procure flange, gasket and hardware. Field weld flange to Well Casing in the upside down position. Extreme care must be taken to assure proper orientation of the flange bolt pattern for correct discharge connection alignment. * FIELD WELDING REQUIRED * * FLANGED WELL CONNECTION NOT PERMITTED IN ALL STATES *
    5. Stainless Steel Hardware for Cap
      Stainless steel hardware is prone to Thread Galling, making it difficult to assemble and disassemble during installation and well pump maintenance. If galling occurs, hardware can snap or break, requiring replacement materials.
    6. Optional: Spider Torque Arrestor
      Fabricated from multiple pieces, not a solid cast component.
    7. Spool Supplied With Only ONE Pressure Zone Tapping
      Unable to provide both, Water Sampler Valve and Pressure Transducer into the submersible pump pressure zone.
    8. Flanged Discharge Connection
      Standard discharge connection is a flange. Boshart provides adapters to transition from flange to threaded, welded, or mechanical joint.
    9. Spool and Discharge Body are Coated with NSF 61 Certified Baked Epoxy
      Paint is not impervious to moisture. Moisture can penetrate beneath perfectly applied paint, causing the spool and discharge body to rust from within. * Barrier Protection Only *
    Monitor Pitless Unit
    6" - 36" available well sizes
    1. Standard: Depth Test Block
      Mandatory in some states. Factory installed ready to use. (3) 1/4″NPT tappings available for compressor, gage and air test line.
    2. Standard: Upper Case and Lift-Out Pipe
      Full Assembly Engineered and Fabricated at factory to Job / Customer Specifications, Complying with local and state codes. * FULL ASSEMBLY FABRICATED AT FACTORY *
    3. Factory Welded Upper Case to Discharge Body
      Welded by Certified Welders at the Factory to Customer Specifications. * NO FIELD WELDING REQUIRED *
    4. Well Casing Connections available from Factory:
      Welded, Threaded, Mechanical Joint (Coupling Included), Flanged
    5. Moly Lube Coated Stainless Steel Hardware for Cap
      Nuts are Moly Lube Coated to prevent Thread Galling. Thread Galling is common when stainless steel hardware is not Moly Lube Coated.
    6. Standard: Spider Torque Arrestor or Hold Down Hooks
      8″ = Spider Torque Arrestor – One Solid Cast Iron Component 10″, 12″ and Larger = Hold Down Hooks Hold Down Hooks create superior support / structure to prevent rotation during motor start-up and for higher pressure artesian well applications.
    7. Spool Supplied With TWO Pressure Zone Tappings
      Two pressure zone tappings to accommodate Water Sampler Valve and Pressure Transducer into the submersible pump pressure zone.
    8. Discharge Connection Supplied From Factory to Customer Specification
      Flanged, Welded, Threaded, Mechanical Joint (w/ or w/o Coupling)
    9. Spool and Discharge Body are Hot Dip Galvanized (Lead Free Zinc)
      Zinc is more electronegative than steel / iron, making Zinc the sacrificial material. When the base steel / iron is exposed, due to a scratch, the base metal is cathodically protected by the sacrificial Zinc coating. The surrounding Zinc is slowly consumed, protecting the base metal at all times. * Zinc provides an Impervious Barrier and Cathodic Protection *

    * Thread Galling is common when the stainless steel surfaces of male and female threads are placed under pressure, during assembly or disassembly. The friction and stress breaks down the self-generated oxide film, causing the two parts to seize (gall). This type of galling is often referred to as “COLD WELDING”.

    * Please contact us today for your RFQ – Freight Included *

    Let’s make your next installation quick and simple by specifying a Monitor Pitless Unit.

     

    • Baker Manufacturing Co, LLC
    • 133 Enterprise Street
    • Evansville, WI 53536
    • Phone: 800-356-5130
    • Fax: 608-882-3777
    • Campbell Manufacturing, LLC
    • 127 E Spring Street
    • Bechtelsville, PA 19505
    • Phone: 610-367-2107
    • Fax: 610-369-3580
    • Visit Monitor Industrial Products Website
    • Visit Monoflex Environmental Products Website
    • TRADE ORGANIZATION MEMBERSHIPS
    • CERTIFICATIONS

    • ISO 9001:2015

    •  

    •  

    • NSF/ANSI 372

    • Campbell

    •  

    •  NSF/ANSI 372

    • Monitor Residential

    •  

    • NSF/ANSI 61

    • Monitor Industrial

    • © 2024 Baker Manufacturing Co., LLC · All rights reserved |
    • Sitemap

    Web Development done by NAVEO in Menomonee Falls, WI