Featured Products

Yard Hydrants

Pitless Adapters

Well Caps

Torque Arrestors

Torque Arrestor

Well Diagram

Well Diagram

Residential

Industrial

Environmental

Video

More Information

Where to Buy

Well Diagram

The quality water system products described here and illustrated on the front page are some of the Baker Water Systems products used in a typical well system. (The section in the catalog where these items can be found is located in parentheses)

This list and the illustration on the front page are not intended as an installation guide. Check local codes for actual requirements and restrictions.

CHECK VALVE
(Section G) Located at the top of the pump, it prevents backflow into the pump and holds the head of water in the system.
BRASS ROPE ADAPTER
(Section A) Connects the Pitless Adapter and the Submersible Pump with Safety Rope.
IDEAL CLAMPS
(Section Q) All-stainless steel clamps for dependable connections between Pipe and Insert Fittings or Torque Arrestor.
3M™ HEAT SHRINK SPLICE KIT
(Section S) For waterproof electric cable splices in submersible pump installations.
TORQUE ARRESTOR
(Section R) Installed directly above Submersible Pumps to protect pump and well components from starting torque damage.
SAFETY ROPE
(Section R) A safety line from the top of the well to the pump.
CABLE TIE
(Section R) Fastens Cable to Drop Pipe
CABLE GUARD
(Section R) U.S. Patent #6,595,284 Protects submersible cable wires from abrading against sides of well. Two styles available: Self-Clamping or Snap-in.
PITLESS ADAPTER
(Section M) Provides a watertight, sanitary, removable connection between the pump and the house. Installed in casing below the frost line to prevent freezing.
BRASS INSERT FITTING
(Section A) Provides connection between poly pipe and pipe thread of Pitless Adapter.
WATERTIGHT WELL CAP
(Section L) Inner gasket compresses to outside diameter of casing to provide a watertight seal. Top of cap removes easily to access well for service.
WELL SEAL
(Section K) Used in above-ground installations to provide a positive seal inside casing.
CHECK VALVE
(Section G) On pump installations, a Check Valve installed near the tank inlet holds water in the tank when the pump is idle.
TANK TEE
(Section O) Connects water line from pump to pressure tank and service line from tank to house. Taps are provided to accept Pressure Switch, Pressure Gauge, Drain Valve, Relief Valve, Snifter Valve, etc.
DRAIN VALVE
(Section H) For easy draining of the system.
BRASS NIPPLE
(Section D) Male threads allow attachment of Pressure Switch to Tank Tee.
RELIEF VALVE
(Section I) Protects against pressure build-up. Should be used on any system where the pump could develop greater pressure than the maximum rating of the system.
PRESSURE GAUGE
(Section R) Measures water pressure in Pressure Tank.
PRESSURE SWITCH
(Section S) Signals the pump to start when the water system drops to a preset low pressure, and to stop when the high pressure mark is reached.
SQUARE D SAFETY SWITCH
(Section S) For electric control and distribution to the pump.
LIGHTNING ARRESTOR
(Section S) Protects pump motor & controls from voltage surges caused by lightning, switching loads, and power line interference.
BALL VALVE
(Section H) Acts as a shutoff valve on the supply line from the tank to the house.
WATER FILTER
(Section T) A point-of-entry, whole-house-filter that removes rust particles, sand, etc. from supply water.

Featured Products

Yard Hydrants

Pitless Adapters

Well Caps

Torque Arrestors

Well Diagram

Residential

Filtration Products

Filter Cartridges and Housings

Sediment Filters

Taste & Odor Filters

Special Application Filters

Plastic Filter Housings

Stainless Steel Filter Housings

Sediment Cartridges

Taste and Odor Cartridges

Special Application Cartridges

Pleated Cartridges

Water Treatment Systems

Water Treatment Systems

Spin Down Filters & Replacement Parts

Spin Down Sediment Filters

Spin Down Screen & Strainer

Spin Down Filter Replacement Parts

Specialty Filters

Specialty Filters

Filter Parts and Installation Kits

Filter Parts and Installation Kits

Metering Pumps

Electronic Metering Pumps

Chemical Metering Pumps

Ultraviolet Disinfection Systems

Ultraviolet Disinfection Systems

Water Well Products

Pitless Adapters

Brass Slide Adapters

Weld On Pitless Adapters

Clamp on Pitless Adapters

Pitless Units

Threaded Pitless Units

Kwikonect Pitless Units

Pressurized Pitless Units

Flowing Wells Pitless units

DQ Series Pitless Units

PJ Pitless Units

Pipe Fittings for Pitless Installations

Well Caps & Seals

Campbell Watertight Well Caps

Monitor Watertight Caps

Turtle Caps

Ventilated Well Caps

Caps for Jet Pumps

Snorkel Vent Assembly

Screened Air Vent for Well Cap

Well Cap Cable Seals

Cast Iron Well Seals

ABS Well Seals

Tank Tees and Tank Fittings Packages

Red Brass Tank Tees & Crosses

Red Brass Union Tank Crosses

Monitor Brass Tees

Tank Manifolds and Crosses

Tank Fitting Packages

Hydrants & Faucets

Campbell Frost Proof Hydrants

Monitor Magnum Frost proof Hydrant

Campbell Frost Proof Wall Faucets

Driven Well Equipment

Well Points

Pitcher Pumps

Cup Leathers & Drive Shoes

Water Well Accessories

Insert Fittings - Metal

Red Brass Insert Fittings

Yellow Brass Insert Fittings

Steel Insert Fittings

Stainless Steel Insert Fittings

Insert Fittings - Threaded Metal

Imported Red Brass Threaded Fittings

Imported Malleable Iron Fittings