Residential

Filtration Products

  • Filter Cartridges and Housings

  • Water Treatment Systems

  • Spin Down Filters & Replacement Parts

  • Specialty Filters

  • Filter Parts and Installation Kits

  • Metering Pumps

  • Ultraviolet Disinfection Systems

Water Well Products

  • Pitless Adapters

  • Pitless Units

  • Well Caps & Seals

  • Tank Tees and Tank Fittings Packages

  • Hydrants & Faucets

  • Driven Well Equipment

Water Well Accessories

  • Insert Fittings - Metal

  • Insert Fittings - Threaded Metal

  • Insert Fittings - Plastic

  • Fittings - Schedule 40

  • Fittings - Compression

  • Nipples and other Fittings

  • Check and Foot Valves

  • Plumbing and Misc. Valves

  • Pump Jacks

  • Hand Pumps

  • At the Well Concept

  • Miscellaneous Well Accessories

Installation and Electrical Accessories

  • Installation Accessories

  • Ideal Clamps

  • Pressure Switches

  • Torque Stop

  • Torque Arrestor

  • Pump & Alarm Switches

  • Control and Alarm Panels

  • Electrical Installation Accessories

Sewage Pump Disconnects

Industrial

Environmental

Visit our e-stores

FILTER IT

OUTLET CENTER

Well Diagram

The quality water system products described here and illustrated are some of the Baker Water Systems products used in a typical well system. This list and the illustration are not intended as an installation guide. Check local codes for actual requirements and restrictions.


©2012 Baker Manufacturing Company, LLC null

CHECK VALVE

Located at the top of the pump, it prevents backflow into the pump and holds the head of water in the system.

BRASS ROPE ADAPTER

Connects the Pitless Adapter and the Submersible Pump with Safety Rope.

IDEAL CLAMPS

All-stainless steel clamps for dependable connections between Pipe and Insert Fittings or Torque Arrestor. 3M™

HEAT SHRINK SPLICE KIT

For waterproof electric cable splices in submersible pump installations.

TORQUE ARRESTOR

Installed directly above Submersible Pumps to protect pump and well components from starting torque damage.

SAFETY ROPE

A safety line from the top of the well to the pump.

CABLE TIE

Fastens Cable to Drop Pipe

CABLE GUARD

U.S. Patent #6,595,284 Protects submersible cable wires from abrading against sides of well. Two styles available: Self-Clamping or Snap-in.

PITLESS ADAPTER

Provides a watertight, sanitary, removable connection between the pump and the house. Installed in casing below the frost line to prevent freezing.

BRASS INSERT FITTING

Provides connection between poly pipe and pipe thread of Pitless Adapter.

WATERTIGHT WELL CAP

Inner gasket compresses to outside diameter of casing to provide a watertight seal. Top of cap removes easily to access well for service.

WELL SEAL

Used in above-ground installations to provide a positive seal inside casing.

CHECK VALVE

On pump installations, a Check Valve installed near the tank inlet holds water in the tank when the pump is idle.

TANK TEE

Connects water line from pump to pressure tank and service line from tank to house. Taps are provided to accept Pressure Switch, Pressure Gauge, Drain Valve, Relief Valve, Snifter Valve, etc.

DRAIN VALVE

For easy draining of the system.

BRASS NIPPLE

Male threads allow attachment of Pressure Switch to Tank Tee.

RELIEF VALVE

Protects against pressure build-up. Should be used on any system where the pump could develop greater pressure than the maximum rating of the system.

PRESSURE GAUGE

Measures water pressure in Pressure Tank.

PRESSURE SWITCH

Signals the pump to start when the water system drops to a preset low pressure, and to stop when the high pressure mark is reached.

SQUARE D SAFETY SWITCH

For electric control and distribution to the pump.

LIGHTNING ARRESTOR

Protects pump motor & controls from voltage surges caused by lightning, switching loads, and power line interference.

BALL VALVE

Acts as a shutoff valve on the supply line from the tank to the house.

WATER FILTER

A point-of-entry, whole-house-filter that removes rust particles,sand, etc. from supply water.